Pular para o conteúdo

KNX guides

DALI vs KNX: which one for lighting control, and how to combine them

DALI and KNX are both open standards, but they solve different problems. DALI is a lighting control bus that talks to drivers and ballasts. KNX is a building automation bus that controls lighting, blinds, HVAC, energy and security together. Most large projects use both: DALI for the luminaires, KNX for the rest of the building, joined by a KNX-DALI gateway. This guide explains the differences and how to plan each option.

1. What DALI is

  • DALI (IEC 62386) is a two-wire digital bus between a controller and lighting devices: LED drivers, ballasts, sensors and push-button interfaces.
  • One DALI line supports up to 64 control gear addresses, 16 groups and 16 scenes. DALI-2 adds standardised control devices (sensors and input units) on the same line.
  • Each driver is addressed individually, so luminaires can be dimmed, grouped and monitored (lamp failure, operating hours) without rewiring.
  • The DALI bus needs its own bus power supply, often built into the gateway or controller.

2. What KNX is

  • KNX (ISO/IEC 14543-3) is a building automation standard. Sensors and actuators from hundreds of manufacturers share one bus and are programmed with one tool, ETS.
  • It covers lighting, blinds and shading, heating and cooling, energy metering, access and visualisation in one system.
  • Lighting on KNX can use switching actuators, dimming actuators (leading or trailing edge, 0/1-10 V) or a KNX-DALI gateway.

3. Side-by-side comparison

  • Scope: DALI controls lighting only. KNX controls the whole building.
  • Size of one segment: DALI: 64 drivers per line. KNX: up to 256 devices per line, and many lines and areas per project.
  • Dimming quality: DALI addresses each driver digitally, with smooth dimming and colour control (DT8 for tunable white and RGB). KNX dimming actuators dim per channel, not per luminaire.
  • Feedback: DALI reports driver and lamp status. KNX reports the status of every function in the building.
  • Commissioning: DALI uses the gateway tool or an app to address drivers. KNX uses ETS for all devices.
  • Cost: for many luminaires in one room, DALI drivers plus one gateway are usually cheaper than many KNX dimming channels. For a few circuits, KNX actuators are simpler.

4. When to choose which

  • Offices, hotels, retail and hospitals with many LED luminaires: DALI for the luminaires, KNX for rooms, blinds, HVAC and central control.
  • Villas and apartments: KNX dimming actuators are often enough. Use DALI where the designer wants tunable white, per-luminaire scenes or many downlights on one circuit.
  • Lighting-only projects (car parks, warehouses, facades): a standalone DALI system with sensors may be the most economical choice.
  • Projects that will grow: start with KNX as the backbone so lighting, shading and HVAC share the same sensors and visualisation.

5. Combining DALI and KNX with a gateway

  • A KNX-DALI gateway sits on the KNX bus and controls one or two DALI lines. KNX push-buttons, presence detectors and visualisation then switch and dim DALI groups and scenes.
  • Count the drivers per DALI line (maximum 64) and choose single or dual-line gateways accordingly.
  • Check whether the gateway supports DT8 colour control, emergency lighting (DT1) and DALI-2 sensors if the project needs them.
  • Agree early who addresses the DALI drivers: the lighting supplier, the electrician or the KNX integrator.
  • DALI wiring has basic insulation and is not SELV. Follow the driver datasheets and local wiring regulations when routing it next to mains cables.

6. Planning checklist

  • List luminaires per room and which ones must dim, change colour or report status.
  • Decide DALI or KNX dimming per room, then count DALI lines and gateways.
  • Specify DALI or DALI-2 drivers in the lighting schedule, so the luminaire supplier delivers the right drivers.
  • Plan presence and daylight sensors once, on KNX or DALI-2, to avoid duplicated sensors.
  • Include the gateway and DALI bus power supply in the KNX bill of quantities.

Related guides

Compare DALI and KNX lighting devices on KNX MORE

Plan the whole project for free

List your rooms and luminaires in the free KNX project planner and send the request to the KNX MORE team. We reply with a quotation within 24 to 72 hours.

Quick view