KNX group addresses explained: structure, examples and planning tips
Group addresses are how KNX devices talk to each other. This guide explains what a group address is, the address formats, how communication objects and datapoint types fit in, and how to plan a clear group address structure for a project.
1. Individual address vs. group address
Every KNX device has two kinds of address. The individual address (for example 1.2.15) identifies the device itself and follows the topology: area, line, device. ETS uses it to program the device.
A group address (for example 1/0/1) identifies a function, such as “living room ceiling light on/off”. In normal operation devices send and receive telegrams to group addresses, not to individual addresses. A push button sends “on” to 1/0/1, and every actuator channel linked to 1/0/1 switches.
2. Group address formats
ETS can show the same group address in three styles. The address on the bus is the same; only the way it is written and organised changes.
- Three-level (main / middle / sub), for example 1/0/1: main group 0–31, middle group 0–7, sub group 0–255. This is the most common style.
- Two-level (main / sub), for example 1/1: main group 0–31, sub group 0–2047.
- Free (one number), for example 2049: 0–65535.
The address 0/0/0 is reserved for broadcast and is not used for normal functions.
3. Communication objects and links
Each device exposes communication objects, such as “Channel A: switch”, “Channel A: status” or “Button 1: dimming”. In ETS you link these objects to group addresses.
- One group address can be linked to many objects, for example one button that switches four actuator channels.
- One object can be linked to several group addresses, for example a channel that listens to its own button and to a central “all off” address. The object sends only on the first linked address.
- Object flags (communication, read, write, transmit, update) decide whether an object sends, receives or answers read requests.
4. Datapoint types must match
The datapoint type (DPT) defines what the value means. All objects linked to one group address should use the same DPT. Common examples:
- DPT 1.001 switch: 1 bit, on/off.
- DPT 3.007 dimming control: 4 bit, brighter/darker in steps.
- DPT 5.001 percentage: 1 byte, 0–100 %, for dimming values or blind position.
- DPT 9.001 temperature: 2 bytes, in °C.
5. Separate command and status addresses
Use one group address for the command and a separate one for the status feedback. The actuator sends its real state on the status address, so visualisations, touch panels and button LEDs always show the true state, even when a central function or a scene changed it.
6. Planning a group address structure
A clear structure makes a project easier to commission, extend and hand over. A common three-level scheme is:
- Main group = function (for example 1 lighting, 2 blinds and shading, 3 HVAC, 4 scenes and central functions, 5 metering and alarms).
- Middle group = floor or building part (for example 0 ground floor, 1 first floor).
- Sub group = the room or point, with commands and status kept in a fixed pattern.
Example: 1/0/1 ground floor living room light on/off, 1/0/2 its dimming, 1/0/3 its brightness value, 1/0/4 its status. Some teams prefer main group = floor and middle group = function; either works if it is used the same way across the whole project.
7. Practical tips
- Give every group address a clear name, such as “GF Living Ceiling Switch”, so the ETS project reads like documentation.
- Leave free sub groups in every range for later extensions.
- Keep central functions (all off, panic, presence simulation) in their own range.
- Couplers filter telegrams by group address. Linking only what is needed keeps traffic low on every line.
- Hand over the ETS project and a group address list to the owner when the project is finished.
Related guides
Compare push buttons, touch panels and actuators from many manufacturers in the KNX manufacturers directory and the touch panels and switches category.
Plan the whole project for free
List your rooms and devices in the free KNX project planner and send the request to the KNX MORE team.