KNX presence detectors explained: PIR, radar and constant light control
Presence detectors are the sensors that save the most energy in a KNX building. They switch and dim lighting, set back heating and cooling and can close blinds when a room is empty. This guide explains the detector types, the settings you meet in ETS and how to place detectors so they work reliably.
1. Motion detector or presence detector?
- Motion detectors react to larger movements such as walking. They suit corridors, stairs, storage rooms and outdoor areas.
- Presence detectors also detect small movements of a person sitting at a desk, so the light does not switch off while someone is working. They suit offices, meeting rooms, classrooms and living areas.
- Datasheets usually give two ranges: a larger one for walking and a smaller one for seated persons. Plan with the seated range in rooms where people sit.
2. Sensor technologies
- PIR (passive infrared): detects the heat of moving people. Reliable and widely used. It needs a free line of sight and can be disturbed by air vents, heaters and direct sunlight.
- Radar / microwave (for example 24 GHz): detects very small movements, even breathing, and works without line of sight. It can see through thin partitions, so the detection field must be set carefully to avoid false triggers from neighbouring rooms.
- Dual technology: combines PIR and radar to reduce false switching in demanding rooms.
3. Functions of a KNX presence detector
- Lighting channels: switch or dim one or more lighting groups, often with separate behaviour for day and night.
- Brightness measurement: the built-in light sensor keeps the light off when there is enough daylight.
- Constant light control: the detector dims the luminaires so the room keeps a set lux level as daylight changes. It needs dimmable lighting (KNX dimmer, 1-10 V or a KNX-DALI gateway).
- HVAC channel: sends presence to the room thermostat or fan coil controller to switch between comfort and standby.
- Master/slave: in large rooms several detectors work together; slaves report movement and the master controls the light.
4. Settings you meet in ETS
- Follow-up (hold) time: how long the light stays on after the last movement. Short in corridors, longer in offices and meeting rooms.
- Brightness threshold: the lux value below which the light switches on.
- Fully automatic or semi-automatic: semi-automatic switches off by itself but needs a push-button to switch on, which saves more energy in offices.
- Sensitivity and test mode: reduce sensitivity near doors and use the walk test to check the detection field before handover.
5. Placement tips
- Mount detectors at the height given in the datasheet; the detection field shrinks or grows with height.
- Cover every workplace with the seated range, and overlap detection fields slightly in open offices.
- Keep PIR detectors away from AC outlets, heaters and lamps that get hot; do not aim them at windows or doors to corridors.
- In toilets with cubicles, use a presence detector with a long hold time or radar, so the light does not switch off while a cubicle is in use.
- Place the light sensor where it measures the light on the working plane, not direct sunlight.
6. Planning checklist
- List rooms by use (corridor, office, meeting, toilet, classroom, hotel room) and choose motion or presence for each.
- Decide which rooms need constant light control and make sure the lighting there is dimmable.
- Count detectors per room from the seated range and the ceiling height.
- Link presence to HVAC and blinds where it saves energy.
- Add the detectors to the bus current of their line when you size the KNX power supply.
Related guides
- DALI vs KNX: which one for lighting control, and how to combine them
- KNX actuator types: switching, dimming, blinds and HVAC
- How to size KNX power supplies for your project
- KNX installation and programming in Egypt, Saudi Arabia and the UAE
Compare KNX presence and motion detectors on KNX MORE
- KNX sensors: presence, motion, light and climate
- SDK SD-24G KNX presence sensor (24 GHz radar)
- SDK SD-WS02 KNX motion and lux sensor
- Lammin: PIR, microwave and 24 GHz presence detectors
Plan the whole project for free
List your rooms and detectors in the free KNX project planner and send the request to the KNX MORE team. We reply with a quotation within 24 to 72 hours.